CLEAN
VOLUME
INPUT
DRIVE
VOLUME
DRIVE
BRIGHT
LO
HI
BASS
MIDDLE TREBLE REVERB
TONE
RUN
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
iPad, iPad mini®
Tablet or Laptop or Android® device
11
USB Interface -PC, Mac, Ipad or Android
USB: The USB 2.0 audio I/O connector supporting the following:
1. Ability to simultaneously record the RAW untreated sound to channel 1
(left) and the full amplifier sound to the channel 2 (right).
2. Ability to play back USB stereo information to headphones for monitoring.
Link from the Headphone output back into the Auxiliary input with a 3.5mm to
6.5mm stereo jack lead allowing simultaneous USB play back.
This feature will also allow external DSP effects on your DAW to use the RAW
signal as a left input then the effected signal sent directly back to the Aux input for
mixing with the amp “through” signal all via USB and without affecting your direct
sound.
3. Re-Amp Send socket allows for the recorded RAW channel to be sent back
to the amplifier input for re-processing via a standard mono instrument jack lead.
For the best level match, use the HI input on the amplifier front panel. To fine tune
the level, use the Dry Recording Gain control. A good starting position for unity gain
is the12 o’clock position. High output pickups or lots of gain produced by FX pedals
before the amp may require a slight reduction in level via the Dry Recording Gain Level
control to prevent overloading of the input stage in your DAW.
Record out via USB: To run into iPad or iPad mini connect via a Camera USB adaptor, PC/MAC connects via standard A-B USB
cable, for use with the likes of Garage Band ®, Audacity ®, MixPad Audio Mixer ®, Pro Tools and similar. It should be noted that the
audio output of an iPad or iPad mini is disengaged and returned via the USB. This can be picked up via a rear panel monitor switch on
the amplifier headphones in stereo, or if required, routed into a PA system/powered cabinets.
Re-Amp Facility: During recording the amplifier processed signal is sent to the right hand channel. The left hand channel carries
the guitar signal totally unprocessed. On an iPad using Garage Band if the track is recorded in stereo then copied with one track
panned left and the other track panned right, then both raw and processed signals are available independently.
This allows for the re-amplifying of a sound that may have been over processed initially. To re-amp via Garage Band on the iPad, solo
the original channel and record a new one with the link in place from the rear re-amp socket and the guitar input. The newly
processed signal will now appear on the right channel with the guitar direct signal again on the left. Other effects may be added into
the link cable but the guitar original sound will not be recorded. It will instead record to the left channel the sound directly after the
effects with no amplifier and the fully processed signal after the amplifier and effects on the right.
Further explanation, videos, etc can be found at www.laney.co.uk
TIP
TIP
(16 pages)
(12 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels